Utilisateur:AegirLoki/Brouillon

A low-pass ladder filter and its signal flow graph

Un filtre leapfrog est un type de circuit électronique actif qui émule le comportement d'un filtre passif en échelle. ladder filter. Ce filtre est connu sous d'autre noms : active-ladder or multiple feedback filter. The arrangement of feedback loops in the signal flow-graph of the simulated ladder filter inspired the name leapfrog filter. The leapfrog filter maintains the low component sensitivity of the passive ladder filter that it simulates.

Synthesis

Generic ladder filters with either (a) voltage input/voltage output, (b) current input/voltage output, (c) voltage input/current output or (d) current input/ current output. The output may also be the voltage across or the current through an internal component of the last element.

The definition and synthesis of leapfrog filters is described by Temes & LaPatra, Chen and Wait, Huelsman & Korn.

Synthesis of leapfrog filters typically includes the following steps:

1. Determine a prototype passive ladder filter that has the desired frequency response. Usually a doubly terminated prototype is used.

2. Write the equations relating element current to voltage across the element in a form suitable for expression as a signal-flow graph.

3. Draw the signal-flow graph. The nodes of the signal-flow graph will include both voltages and currents. The branch gains will include impedances and admittances.

4. Convert all nodes of the signal-flow graph to voltages and all impedances to dimensionless transmittances. This is accomplished by dividing all impedance elements by R, an arbitrary resistance and multiplying all admittance elements by R. This scaling does not change the frequency response.

5. Manipulate the signal-flow graph so that the gains feeding each summing node have the same signs. This is done as an implementation convenience. At the completion of this step, typically, all the feedback gains in the signal-flow graph will be +1 and the signs of the gain blocks in the forward path will alternate. As a result, some of the nodes, including the main output, may have a 180° phase inversion. This is usually of no consequence.

6. The gain blocks are implemented with active filters and interconnected as indicated by the signal-flow graph. Often, state variable filters are used for the gain blocks.

7. The final circuit usually has more components than the prototype passive filter. This means the final circuit has degrees of freedom which can be chosen to optimize the circuit for dynamic range and for practical component values.

Examples

Generic filter

Four element ladder filter with voltage input and voltage output

Three stages of signal-flow graph development of a four element ladder filter with voltage input and voltage output.

The design starts out with a known ladder filter of one of the typologies shown in the previous figure. Usually, all the elements of the ladder filter are lossless except the first and the last which are lossy. Using a four element voltage input, voltage output ladder filter as an example, the equations that relate the element voltages and currents are as follows:

$I_{1}=(V_{0}-V_{2})\mathrm {Y_{1}}$

$V_{2}=(I_{1}-I_{3})\mathrm {Z_{2}}$

$I_{3}=(V_{2}-V_{4})\mathrm {Y_{3}}$

$V_{4}=(I_{3})\mathrm {Z_{4}}$

The signal-flow graph for these equations are shown in the second figure to the right. The arrangement of feedback loops in the signal flow-graph inspired the name leapfrog filter. The signal flow graph is manipulated to convert all current nodes into voltage nodes and all the impedances and admittances into dimensionless transmittances. This is equivalent to manipulating the equations either by multiplying both sides by R or by multiplying one side by R/R and distributing the R terms across the subtraction operation. This manipulation changes the equations as follows:

$V_{1}=(V_{0}-V_{2})\mathrm {H_{1}}$

$V_{2}=(V_{1}-V_{3})\mathrm {H_{2}}$

$V_{3}=(V_{2}-V_{4})\mathrm {H_{3}}$

$V_{4}=(V_{3})\mathrm {H_{4}}$

where H₁ = RY₁, H₂ = GZ₂, H₃ = RY₃, H₄ = GZ₄, G = 1/R, V₁ = RI₁, V₃ = RI₃

The signal flow graph is further manipulated so that the gains into each summing node is +1. The result of all the manipulation is shown as the bottom signal-flow graph in the figure. The equations represented by the resulting signal flow graph are as follows:

$-V_{1}=(V_{0}-V_{2})(-\mathrm {H_{1}} )$

$-V_{2}=(-V_{1}+V_{3})\mathrm {H_{2}}$

$V_{3}=(-V_{2}+V_{4})(-\mathrm {H_{3}} )$

$V_{4}=(V_{3})\mathrm {H_{4}}$

The awkward annotation of -V₁ and -V₂ as labels of nodes in the signal flow graph indicates that these nodes present a 180° phase inversion with respect to the signals in the prototype filter.

This manipulation is can be accomplished by a simple procedure:

1. Make all the odd numbered or all the even numbered transmittances negative. The overall phase shift with respect to the prototype will be 0° if the total number of inversions is even.

2. Change all feedback gains to +1.

3. Determine the sign of each node label by counting the number of inversions to that node from the input. If the number of inversions is odd, then the node label is negative.

The signal-flow graph is suitable for implementation. State variable filters that are available in both inverting and non-inverting typologies are often used.

---

Band pass filter

A schematic for a passive band pass electronic filter

Passive circuit

The circuit for a band pass, passive ladder filter is first determined.

The individual components in parallel or series can be combined into general impedances or admittances. For this schematic:

$\mathrm {Z_{1}} ={\frac {s\mathrm {L_{1}} }{s^{2}\mathrm {C_{1}} \mathrm {L_{1}} +s{\frac {\mathrm {L_{1}} }{\mathrm {R_{1}} }}+\mathrm {1} }}$

${\mathrm {Y_{2}} }={\frac {s\mathrm {C_{2}} }{s^{2}\mathrm {C_{2}} \mathrm {L_{2}} +\mathrm {1} }}$

$\mathrm {Z_{3}} ={\frac {s\mathrm {L_{3}} }{s^{2}\mathrm {C_{3}} \mathrm {L_{3}} +1}}$

$\mathrm {Y_{4}} ={\frac {s\mathrm {C_{4}} }{s^{2}\mathrm {C_{4}} \mathrm {L_{4}} +s\mathrm {C_{4}} \mathrm {R_{4}} +1}}$

---

Fichier:Coarse signal flow graph of passive ladder filter.png

The signal flow-graph representation of the ladder filter equations.

Signal-flow graph

The current and voltage variables can be put into cause and effect relationships as follows.

$V_{1}=(I_{0}-I_{2})\mathrm {Z_{1}}$

$I_{2}=(V_{1}-V_{3})\mathrm {Y_{2}}$

$V_{3}=(I_{2}-I_{4})\mathrm {Z_{3}}$

$I_{4}=V_{3}\mathrm {Y_{4}}$

$V_{4}=I_{4}\mathrm {R_{4}}$

A signal flow graph for these equations is shown to the right.

---

Scaled signal-flow graph

For implementation reasons, the current variables may be multiplied by an arbitrary resistance to convert them into voltage variables which also converts all gains to dimensionless values. In this example all currents are multiplied by R. This is accomplished by either multiplying both sides of an equation by R of by multiplying one side by R/R and then distributing the R term over the currents.

The signal flow-graph representation of the ladder filter equations with impedances scaled by R, an arbitrary resistance.

$V_{1}=(V_{0}-V_{2})\mathrm {H_{1}}$

$V_{2}=(V_{1}-V_{3})\mathrm {H_{2}}$

$V_{3}=(V_{2}-V_{4})\mathrm {H_{3}}$

$V_{4}=(V_{3})\mathrm {H_{4}}$

$V_{\mathrm {out} }=(V_{4})\mathrm {H_{5}}$

where H₁ = GZ₁, H₂ = RY₂, H₃ = GZ₃, H₄ = RY₄, H₅ = GR₄, G = 1/R, V₂ = RI₂, V₄ = RI₄

---

Manipulated signal-flow graph

It is convenient for implementation if the gains feeding the summing nodes all have the same sign. In that case, summation can be achieved with a junction of two resisters.

The signal flow-graph representation of the ladder filter equations with impedances scaled by R, an arbitrary resistance. The signs of the gains have been manipulated so that all gains feeding into a node have the same signs.

$V_{1}=(V_{0}+(-V_{2}))\mathrm {H_{1}}$

$-V_{2}=(V_{1}+(-V_{3}))(\mathrm {-H_{2}} )$

$-V_{3}=((-V_{2})+V_{4})\mathrm {H_{3}}$

$V_{4}=V_{3}(\mathrm {-H_{4}} )$

$V_{\mathrm {out} }=(V_{4})\mathrm {H_{5}}$

---

Implementation

Modified Tow-Thomas active biquad filter with summing inputs and complimentary band pass outputs suitable for use in a leapfrog filter. V_BP is the bandpass output, V_BPI is the inverted bandpass output.

All the transmittances H₁ - H₄, in this example, are bandpass filters. They can be implemented with the modified Tow-Thomas active biquad filter. This biquad has both positive and negative bandpass outputs so that it can realize any of the transmittances. This biquad also has summing inputs so it can also implement the summing nodes.

---

Tuning

A leapfrog filter can be difficult to tune because of the complicated feed back. One strategy is to open the feedback loops so that the remaining filter structure is a simple cascade design. Each section can then be tuned independently. The inner sections, H₂ and H₃ have infinite Q and may be unstable when the feedback loops are opened. These stages may be designed with a large, but finite Q so that they can be tuned while the feedback loops are open.

---

References

[[Category:Linear filters]]